By Plumbing Guide for Bathtub Installation
By Plumbing Guide for Bathtub Installation
Blog Article
Just how do you feel about How to Install a Bathtub?
Mounting a bathtub isn't specifically brain surgery, but it does call for solid plumbing, woodworking, as well as often, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably tough project. If the old bathtub is conveniently easily accessible, the job can relocate easily; if you need to open up a wall surface to get rid of the old bathtub as well as place the new tub, the task is a lot harder. In either situation, the job is within a home handyman's skills, although you will require an assistant to vacate the old tub as well as set in the new one. See to it you have actually qualified yourself for the work and are comfortable attempting it. As opposed to working with a specialist to take control of a halfway-completed project, it is better to think about utilizing one before you begin. Possibilities are you may need a specialist plumber to make tube links.
This article will aid you set up a brand-new bathtub in your shower room if you have actually already gotten a brand-new tub and also don't need to change the arrangement of your previous water supply pipes.
Your tools and also material list must consist of the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you ought to do is disconnect the water system. After doing so, switch on the taps to drain pipes any kind of water remaining in the system. The process of getting rid of the existing faucets can be quite bothersome due to the restricted gain access to that is often the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a cloth prepared for the remaining water that will certainly originate from the pipelines. When the supply pipes have been removed, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end offers a link to the existent supply pipes.
If you need to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in location between the faucet and also the sink. Secure the faucet in place with the manufacturer provided backnut. As soon as the faucet is safely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular tap adapters. The former kind should be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Bathtub
Utilizing both wooden boards under its feet, put the bathtub in the called for setting. The wooden boards are useful in uniformly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny factors.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the level and readjusting the feet on the bath tub till the level reviews level.
To mount taps, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; after that do the same for the various other tap.
Activate the water supply and also examine all joints and also new pipework for leakages and tighten them if necessary. Load the bath tub as well as additionally check the overflow outlet as well as the normal outlet for leakages.
Finally, take care of the bath paneling as defined in the supplier's instruction manual. Tiling and sealing around the bathtub must wait up until the bath tub has actually been made use of a minimum of once as this will settle it right into its final setting.
Planning for the Installation
To start with, the sustaining structure supplied with the bathroom needs to be fitted (if called for) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to see to it that if the tap comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the adaptable faucet ports to the bottom of both taps making use of 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath should now be ready to be fitted in its last position.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to permeate the wall between the bathroom as well as the tiling, bring about complications with dampness and feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to securing, to enable the motion experienced when the tub is in usage. The sealant can fracture rather early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly offered on the market. It is recommended to fit the ceramic tiles using water-resistant or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a reader on A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that excerpt was worthwhile. Do you know about somebody else who is truly interested in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Please feel free to promote it. Bless you for your time. Don't forget to visit our site back soon.
Try Here Report this page